CORONA 2.4G 7CH GR7SF S-FHSS Compatible Receiver With Gyro for Futaba T6J T8J T10J T14SG

The New CORONA 2.4 7CH GR7SF S-FHSS Compatible Receiver With Gyro for Futaba T6J T8J T10J T14SG Description: Brand: CORONA Item Name: CORONA GR7SF receiver Voltage Range :3.6~8.5V Operating Current: 60mA max Operation temperature: -10~70 degC Latency: 6.8mS Sensitivity: about -96dBm Weight: 16g Compatibility: CORONA 2.4GHz S-FHSS Compatible Receiver is designed to use with FUTABA S-FHSS 2.4GHz transmitters, such as T6J,T8J,T10J and T14SG under S-FHSS protocol mode. Features: Mode supply: No mixer, Dual-aileron, V-tail mixer, Delta mixer Independent simple gyro gain adjustment for Aileron, Elevator and Rudder S.BUS output support expanding servo channels(will take effect in new version). Support gyro function switch on and off in flying by Switching signal of CH5 will take effect in new version. Bind procedure: Turn on the S-FHSS transmitter Connect the battery to the receiver while pressing receiver’s F/S button. Red LED light on and Green LED off when searching signals, and turn to Green LED light on and Red LED off indicate bind is succeeded. User Manual, Click here Package included: 1x CORONA 2.4 7CH GR7SF S-FHSS Compatible Receiver With Gyro

Features:

• Lightweight (16g)

• Compatible with S-FHSS 2.4Ghz air systems

• 7 channels

• Built in 3 axis stabiliser

• 5 stabilizer modes

• Supports SBus

• Compact design (54 x 32 x 13mm)

• Failsafe and battery failsafe

• Extremely low latency

• Fast frame rates

• Hops from frequency to frequency in a pseudorandom sequence

• Advanced algorithms create a secure frequency

Specifications:

Model : GR7SF

Input Voltage : 3.6 - 8.5V

Operating Current : 60mA max

Battery Failsafe Voltage : 3.8V

Latency : 6.8mS

Sensitivity : approx -96dBm

Dimensions : 54 x 32 x 13mm

Weight : ~16g

Note: This is not a Futaba brand receiver. Futaba, FASST and FHSS are trademarks of Futaba Co (JP).

Voltage Range :3.6~8.5V

Operating Current: 60mA max

Operation temperature: -10~70 degC

Latency: 6.8mS

Sensitivity: about -96dBm

Weight: 16g

 

Bind procedure:

· Turn on the S-FHSS transmitter

· Connect the battery to the receiver while pressing receiver’s F/S button.

· Red LED light on and Green LED off when searching signals, and turn to Green LED light on and Red LED off indicate bind is succeeded.

 

Installation Guide:

Make sure that your plane has good status before installing GR7SF and other electrical device on it.

The receiver need to be firmly mounted near the gravity of the plane by double side tape, refer to
Ensure the axis direction is out of four kind types description below. Fixed GR7SF reference the information mentioned in axis description pictures on receiver’s box.



Turn on S-FHSS transmitter, turn off any mixer feature on the transmitter, firstly set stick trimming and sub-trim parameters to zero .Preset all sensitivity at about 40~60%, Select the proper mode of mixer on GR7SF and power on it, check and adjust aileron, elevator or rudder to the neutral position of control surface. Adjustment can be done by stick trimming on the transmitter. If mode selection and sensitivity changed, please power the GR7SF again to let new feature take effect. 

Check all servo controlling that you need under flying is correct. Reverse the servo direction on the transmitter if need. Roll the model along the x, y or z axis alone to check the compensation direction that you want.
If compensation direction is reversed, set the sensitivity value reverse. If any sensitivity changed, please power the GR7SF again to let new feature take effect.

 

Fail-safe setting:

GR7SF set failsafe on the S-FHSS transmitter just like the operation of the FUTABA receivers.

We highly recommend you set failsafe feature while flying your models. An example of a useful Failsafe setting would be to shut down the model’s throttle, so that it does not fly or drive away uncontrolled.